PRODUCTS & CONSTRUCTION SERVICES
Detailed scope of work for each product.
Select a product below to see the typical work that may be included. The signed home-improvement contract, approved plans, permits and written change orders determine the exact scope for each property.
Roof ReplacementShingle / cool roof / complete reroof
Typical scope of work
- Protect landscaping, driveway, walls and adjacent work areas before tear-off.
- Remove contracted roofing layers and dispose of roofing debris.
- Inspect exposed roof decking and identify visible damaged or deteriorated sheathing.
- Replace damaged decking when included in the contract or approved as additional work.
- Install specified underlayment, valley protection, drip edge and required flashing components.
- Flash plumbing vents, roof vents, walls, chimneys, skylights and other penetrations included in the scope.
- Install selected shingle or cool-roof system according to approved project documents and manufacturer requirements.
- Install or improve attic exhaust ventilation, including ridge or roof vents, when specified.
- Complete final cleanup, accessible magnetic sweep and project walkthrough.
Hidden wood damage, structural repairs, hazardous materials and major roof-deck replacement are included only when written into the contract or approved by change order.
Flat / Low-Slope RoofingModified bitumen and low-slope roof systems
Typical scope of work
- Protect the work area and remove existing low-slope roofing where tear-off is included.
- Inspect the exposed substrate and repair damaged roof deck when contracted.
- Prepare the surface and install the specified base sheet, membrane or approved low-slope assembly.
- Install modified-bitumen or other contracted roofing system.
- Flash parapets, walls, drains, scuppers, pipes, curbs and roof penetrations.
- Install termination bars, edge metal and sealant details where required by the system.
- Address drainage or slope corrections only where specifically included.
- Inspect seams, terminations and penetrations and complete final cleanup.
Structural slope changes, ponding-water correction and extensive substrate replacement are separate unless specifically included.
Windows & DoorsRetrofit windows, sliders and selected doors
Typical scope of work
- Field-measure openings and confirm window or door sizes, configurations and operation.
- Protect interior and exterior finishes adjacent to each opening.
- Remove existing components as required for the selected retrofit or replacement method.
- Prepare openings and make minor installation-related substrate corrections included in the contract.
- Install units plumb, level and square using approved fastening methods.
- Apply perimeter flashing, insulation and weather sealants appropriate to the installation.
- Install contracted trim, stops, screens and finish components.
- Adjust locks, rollers and hardware, clean glass and complete final walkthrough.
Structural header changes, extensive stucco reconstruction, interior casing and hazardous-material work are separate unless included.
Attic Insulation & Air SealingInsulation, air sealing and duct insulation
Typical scope of work
- Inspect accessible attic conditions, existing insulation, ventilation and visible ductwork.
- Protect attic access and interior travel path.
- Remove existing insulation only when removal is part of the contract.
- Seal accessible ceiling penetrations, top plates and common air-leak locations when included.
- Install baffles or dams to maintain required clearances around vents and heat-producing equipment.
- Install contracted insulation to the specified depth and target R-value.
- Wrap or improve accessible duct insulation where included.
- Confirm ventilation pathways remain open and clean the work area.
Rodent remediation, mold, asbestos and unsafe electrical conditions require separate evaluation.
HVAC & DuctworkHeating, cooling, heat pumps and ducts
Typical scope of work
- Review existing equipment, installation locations, electrical capacity and accessible duct conditions.
- Remove and dispose of contracted existing HVAC equipment.
- Install new indoor and outdoor equipment on approved platforms or pads.
- Install or reconnect refrigerant piping, condensate drainage, electrical and gas connections as applicable.
- Replace, repair, seal or insulate ductwork where included in the project.
- Install thermostat, disconnects and required control equipment.
- Pressure-test, evacuate and charge refrigerant system as applicable.
- Start, test and verify heating, cooling, airflow and thermostat operation.
Duct redesign, asbestos duct removal and electrical-service upgrades are separate unless included in the signed scope.
Solar & BatterySolar PV, battery storage and electrical integration
Typical scope of work
- Review electric usage goals, roof area, shading, service equipment and proposed equipment locations.
- Prepare project design and permit/interconnection documentation as applicable.
- Verify roof readiness and coordinate any contracted roof work before installation.
- Install approved roof attachments, flashing, racking and photovoltaic modules.
- Install inverter or microinverter equipment, disconnects, rapid-shutdown devices and required labeling.
- Install battery storage and backup equipment when included.
- Complete electrical connections to service equipment according to approved design.
- Test, commission and support required inspection and utility permission-to-operate procedures.
Utility approval, export rules, incentives and program eligibility are determined by the applicable utility or program administrator.
Electrical & Main Panel UpgradesService equipment, subpanels and dedicated circuits
Typical scope of work
- Evaluate service rating, panel condition, breaker space and planned project loads.
- Perform load calculations when required.
- Coordinate permit and utility disconnect/reconnect when service equipment is replaced.
- Remove contracted panel or service equipment and install listed replacement equipment.
- Install correctly sized breakers, grounding and bonding components included in the scope.
- Add subpanels or dedicated HVAC, EV, battery, solar or appliance circuits when contracted.
- Label circuits and complete project-specific safety corrections within the agreed scope.
- Test the completed electrical work and coordinate inspection as applicable.
Whole-house rewiring, trenching and utility-side upgrades are separate unless explicitly included.
Heat Pump Water HeaterHigh-efficiency electric water heating
Typical scope of work
- Review existing water-heater location, plumbing, electrical capacity and equipment clearances.
- Shut down, disconnect and remove the contracted existing unit.
- Install heat-pump water heater with required pan and seismic restraints.
- Connect hot/cold water piping, shutoffs and pressure-relief components.
- Install condensate routing as required by the equipment and installation location.
- Install or connect the dedicated electrical circuit when included.
- Fill, leak-test and configure equipment operating mode.
- Verify heating operation and complete required inspection where applicable.
Exterior Coatings & PaintSurface preparation, repairs and exterior finishes
Typical scope of work
- Protect roofing, windows, landscaping and adjacent surfaces.
- Wash or clean exterior surfaces as appropriate for the coating system.
- Scrape or sand loose material and prepare surfaces included in the scope.
- Patch contracted stucco cracks and minor surface defects.
- Caulk selected joints and prime repaired or bare areas as required.
- Apply the selected exterior coating or paint system at the required coverage.
- Complete trim, fascia, eaves and other contracted finish areas.
- Remove protection, perform touch-ups and complete final walkthrough.
Major stucco reconstruction, extensive wood replacement and underlying waterproofing failures are separate unless included.
Bathroom RemodelingWalk-in showers and complete bathroom renovation
Typical scope of work
- Protect access routes and adjacent areas before demolition.
- Remove contracted tub/shower, tile, flooring, fixtures, cabinetry and finishes.
- Complete framing or blocking work included in the design.
- Rough-in plumbing and electrical for contracted fixture changes.
- Install shower pan, waterproofing and approved wall/backer materials.
- Install tile or wall-surround system, flooring, vanity, toilet and plumbing fixtures.
- Install lighting, exhaust fan, mirror, accessories and finish trim included in the contract.
- Patch and paint affected areas, test fixtures and complete final cleanup.
Hidden water damage, structural work and major plumbing relocation may require additional approved scope.
Kitchen RemodelingCabinets, counters, lighting, plumbing and finishes
Typical scope of work
- Protect work areas and remove contracted cabinets, countertops, appliances and finishes.
- Complete framing and drywall changes included in the approved layout.
- Rough-in plumbing, lighting, outlets and appliance circuits as contracted.
- Install cabinets and verify alignment, level and appliance clearances.
- Template and install countertops and backsplash.
- Install sink, faucet, disposal and appliance connections included in the scope.
- Install flooring, baseboards, lighting devices and finish trim where contracted.
- Patch/paint affected surfaces, test utilities and complete cleanup.
Foundation RetrofitSeismic anchorage and cripple-wall bracing
Typical scope of work
- Inspect accessible crawlspace and visible foundation/framing connections.
- Determine whether the retrofit can follow an approved prescriptive detail or requires engineered plans.
- Obtain permits where required and establish safe crawlspace work access.
- Install approved anchor bolts or foundation plates at specified locations and spacing.
- Add sill-plate, blocking and framing connectors called for by the retrofit details.
- Install structural plywood/sheathing and specified nailing for cripple-wall bracing where applicable.
- Install hold-downs, straps, clips, posts or other structural hardware when included in the approved plan.
- Complete required inspection before covering structural work and remove construction debris.
Foundation replacement, underpinning, major settlement correction, engineering and extensive damaged framing are separate unless specifically included.
Gutters & DrainageGutters, downspouts and roof-water management
Typical scope of work
- Remove existing gutters and downspouts when replacement is included.
- Inspect visible fascia attachment areas and complete contracted fascia repairs.
- Fabricate and install gutters with slope toward designated outlets.
- Install downspouts, elbows and attachment straps at agreed locations.
- Install extensions or drainage routing included in the contract.
- Seal outlets/end caps and test accessible runs for drainage flow.
- Remove contracted old materials and clean the work area.
Patio Covers & General ConstructionPatios, framing, repairs and coordinated General B work
Typical scope of work
- Confirm layout, dimensions, attachment conditions and permit/design requirements.
- Prepare the work area and install required footings or support foundations.
- Install posts, beams, framing and structural connections according to the approved scope.
- Install roof/cover materials, flashing and waterproofing components where applicable.
- Complete contracted electrical, lighting, stucco, siding, trim or paint work.
- Coordinate required inspection and complete final cleanup.
General B work varies by project and is defined by the signed contract, plans and written change orders.
Framing & Structural RepairsWalls, sheathing, posts, beams and structural repairs
Typical scope of work
- Document accessible existing conditions and define the repair area.
- Review permit and engineering requirements before structural alteration.
- Shore or support affected structure when required by the approved repair method.
- Remove contracted damaged or obsolete framing.
- Install new lumber, sheathing and approved structural connectors according to project details.
- Complete blocking, fastening and load-path connections required by the scope.
- Coordinate inspection before structural work is covered where required.
- Restore affected finishes only to the extent included in the contract.
Water Damage / ReconstructionSelective demolition and reconstruction after moisture damage
Typical scope of work
- Identify visible damaged areas and confirm that the known moisture source is corrected or included for repair.
- Establish work-area protection appropriate to the contracted work.
- Remove affected drywall, insulation, flooring or other materials included in the scope.
- Coordinate drying or dehumidification where required.
- Repair damaged framing or substrate when included and authorized.
- Reinstall insulation, drywall, texture, paint, flooring and finishes included in reconstruction.
- Clean work areas and complete final walkthrough.
Environmental testing, regulated mold remediation, asbestos and lead work may require independent specialty contractors and are not automatically included.
Scope disclosure: These descriptions explain typical construction work that may be available through California Energy Efficient Construction. They are not a universal promise of inclusions. The signed contract for the specific homeowner, approved plans, permits, manufacturer requirements, field conditions and written change orders determine the actual scope. Product availability is separate from eligibility for any public program, rebate, incentive or financing option described elsewhere on this website.